FreeBSD Man Pages

if_sis(4)

NAME

     sis -- SiS 900, SiS 7016 and NS DP83815 Fast Ethernet device driver

SYNOPSIS

     device miibus
     device sis

DESCRIPTION

     The sis driver provides support for PCI Ethernet adapters and embedded
     controllers based on the Silicon Integrated Systems SiS 900 and SiS 7016
     Fast Ethernet controller chips.

     This driver also supports adapters based on the National Semiconductor
     DP83815 (MacPhyter) PCI Ethernet controller chip.

     The SiS 900 is a 100Mbps Ethernet MAC and MII-compliant transceiver in a
     single package.  It uses a bus master DMA and a scatter/gather descriptor
     scheme.  The SiS 7016 is similar to the SiS 900 except that it has no
     internal PHY, requiring instead an external transceiver to be attached to
     its MII interface.  The SiS 900 and SiS 7016 both have a 128-bit multi-
     cast hash filter and a single perfect filter entry for the station
     address.

     The NS DP83815 is also a 100Mbps Ethernet MAC with integrated PHY.  The
     NatSemi chip and the SiS 900 share many of the same features and a fairly
     similar programming interface, hence both chips are supported by the same
     driver.

     The sis driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The
		  user can manually override the autoselected mode by adding
		  media options to rc.conf(5).

     10baseT/UTP  Set 10Mbps operation.  The ifconfig(8) mediaopt option can
		  also be used to select either `full-duplex' or `half-duplex'
		  modes.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8)
		  mediaopt option can also be used to select either
		  `full-duplex' or `half-duplex' modes.

     The sis driver supports the following media options:

     full-duplex  Force full duplex operation

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The sis driver supports Silicon Integrated Systems SiS 900 and SiS 7016
     based Fast Ethernet adapters and embedded controllers, as well as Fast
     Ethernet adapters based on the National Semiconductor DP83815 (MacPhyter)
     chip.  Supported adapters include:

     o	 @Nifty FNECHARD IFC USUP-TX

     sis%d: couldn't map interrupt  A fatal initialization error has occurred.

     sis%d: watchdog timeout  The device has stopped responding to the net-
     work, or there is a problem with the network connection (e.g. a cable
     fault).

     sis%d: no memory for rx list  The driver failed to allocate an mbuf for
     the receiver ring.

     sis%d: no memory for tx list  The driver failed to allocate an mbuf for
     the transmitter ring when allocating a pad buffer or collapsing an mbuf
     chain into a cluster.

     sis%d: chip is in D3 power state -- setting to D0	This message applies
     only to adapters which support power management.  Some operating systems
     place the controller in low power mode when shutting down, and some PCI
     BIOSes fail to bring the chip out of this state before configuring it.
     The controller loses all of its PCI configuration in the D3 state, so if
     the BIOS does not set it back to full power mode in time, it will not be
     able to configure it correctly.  The driver tries to detect this condi-
     tion and bring the adapter back to the D0 (full power) state, but this
     may not be enough to return the driver to a fully operational condition.
     If you see this message at boot time and the driver fails to attach the
     device as a network interface, you will have to perform a warm boot to
     have the device properly configured.

     Note that this condition only occurs when warm booting from another oper-
     ating system.  If you power down your system prior to booting FreeBSD,
     the card should be configured correctly.

SEE ALSO

     arp(4), miibus(4), netintro(4), ng_ether(4), polling(4), ifconfig(8)

     SiS 900 and SiS 7016 datasheets, http://www.sis.com.tw.

     NatSemi DP83815 datasheet, http://www.national.com.

HISTORY

     The sis device driver first appeared in FreeBSD 3.0.

AUTHORS

     The sis driver was written by Bill Paul <wpaul@ee.columbia.edu>.

FreeBSD 5.4		       November 24, 2004		   FreeBSD 5.4

SPONSORED LINKS