FreeBSD Man Pages

tl(4)

NAME

     tl -- Texas Instruments ThunderLAN Ethernet device driver

SYNOPSIS

     device miibus
     device tl

DESCRIPTION

     The tl driver provides support for PCI Ethernet adapters based on the
     Texas Instruments ThunderLAN Ethernet controller chip.

     The ThunderLAN controller has a standard MII interface that supports up
     to 32 physical interface devices (PHYs).  It also has a built-in 10baseT
     PHY hardwired at MII address 31, which may be used in some 10Mbps-only
     hardware configurations.  In 100Mbps configurations, a National Semicon-
     ductor DP83840A or other MII-compliant PHY may be attached to the Thun-
     derLAN's MII bus.	If a DP83840A or equivalent is available, the Thunder-
     LAN chip can operate at either 100Mbps or 10Mbps in either half-duplex or
     full-duplex modes.  The ThunderLAN's built-in PHY and the DP83840A also
     support autonegotiation.

     The tl driver supports the following media types:

     autoselect 	   Enable autoselection of the media type and options.
			   Note that this option is only available on those
			   PHYs that support autonegotiation.  Also, the PHY
			   will not advertise those modes that have been
			   explicitly disabled using the following media
			   options.

     10baseT/UTP	   Set 10Mbps operation

     100baseTX		   Set 100Mbps (Fast Ethernet) operation

     10base5/AUI	   Enable AUI/BNC interface (useful only with the
			   built-in PHY).

     The tl driver supports the following media options:

     full-duplex	   Force full duplex operation

     half-duplex	   Force half duplex operation.

     hw-loopback	   Enable hardware loopback mode.

     Note that the 100baseTX media type is only available if supported by the
     PHY.  For more information on configuring this device, see ifconfig(8).

HARDWARE

     The tl driver supports Texas Instruments ThunderLAN based Ethernet and
     Fast Ethernet adapters including a large number of Compaq PCI Ethernet
     adapters.	Also supported are:

     o	 Olicom OC-2135/2138 10/100 TX UTP adapter
     o	 Olicom OC-2325/OC-2326 10/100 TX UTP adapter
     o	 Racore 8148 10baseT/100baseTX/100baseFX adapter
     o	 Racore 8165 10/100baseTX adapter
     o	 Compaq Netelligent 10/100 Proliant
     o	 Compaq Netelligent 10/100 TX Embedded UTP
     o	 Compaq Netelligent 10/100 TX UTP
     o	 Compaq NetFlex 3P
     o	 Compaq NetFlex 3P Integrated
     o	 Compaq NetFlex 3P w/BNC

DIAGNOSTICS

     tl%d: couldn't map memory	A fatal initialization error has occurred.

     tl%d: couldn't map interrupt  A fatal initialization error has occurred.

     tl%d: device timeout  The device has stopped responding to the network,
     or there is a problem with the network connection (cable).

     tl%d: no memory for rx list  The driver failed to allocate an mbuf for
     the receiver ring.

     tl%d: no memory for tx list  The driver failed to allocate an mbuf for
     the transmitter ring when allocating a pad buffer or collapsing an mbuf
     chain into a cluster.

SEE ALSO

     arp(4), miibus(4), netintro(4), ng_ether(4), ifconfig(8)

HISTORY

     The tl device driver first appeared in FreeBSD 2.2.

AUTHORS

     The tl driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

FreeBSD 5.4		       September 3, 2004		   FreeBSD 5.4

SPONSORED LINKS