FreeBSD Man Pages

vge(4)

NAME

     vge -- VIA Networking Technologies VT6122 PCI Gigabit Ethernet adapter
     driver

SYNOPSIS

     device miibus
     device vge

DESCRIPTION

     The vge driver provides support for various NICs and embedded Ethernet
     interfaces based on the VIA Networking Technologies VT6122 Gigabit Ether-
     net controller chips.

     The VT6122 is a 33/66Mhz 64-bit PCI device which combines a tri-speed MAC
     with an integrated 10/100/1000 copper PHY.  (Some older cards use an
     external PHY.)  The MAC supports TCP/IP hardware checksums (IPv4 only),
     TCP large send, VLAN tag insertion and stripping, as well as VLAN filter-
     ing, a 64-entry CAM filter and a 64-entry VLAN filter, 64-bit multicast
     hash filter, 4 separate transmit DMA queues, flow control and jumbo
     frames up to 16K in size.	The VT6122 has a 16K receive FIFO and 48K
     transmit FIFO.

     The vge driver takes advantage of the VT6122's checksum offload and VLAN
     tagging features, as well as the jumbo frame and CAM filter support.  The
     CAM filter is used for multicast address filtering to provide 64 perfect
     multicast address filter support.	If it is necessary for the interface
     to join more than 64 multicast groups, the driver will switch over to
     using the hash filter.

     The jumbo frame support can be enabled by setting the interface MTU to
     any value larger than the default of 1500 bytes, up to a maximum of 9000
     bytes.  The receive and transmit checksum offload support can be toggled
     on and off using the ifconfig(8) utility.

     The vge driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The
		  user can manually override the autoselected mode by adding
		  media options to rc.conf(5).

     10baseT/UTP  Set 10Mbps operation.  The ifconfig(8) mediaopt option can
		  also be used to select either full-duplex or half-duplex
		  modes.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8)
		  mediaopt option can also be used to select either
		  full-duplex or half-duplex modes.

     1000baseTX   Set 1000baseTX operation over twisted pair.  The ifconfig(8)
		  mediaopt option can also be used to select either
		  full-duplex or half-duplex modes.

     The vge driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.
	    state, it is necessary to force one side of the link to be a mas-
	    ter and the other a slave.	The vge driver configures the ports as
	    slaves by default.	Setting the link0 flag with ifconfig(8) will
	    set a port as a master instead.

     For more information on configuring this device, see ifconfig(8).

HARDWARE

     The vge driver supports VIA Networking VT3119 and VT6122 based Gigabit
     Ethernet adapters including:

     o	 VIA Networking LAN-on-motherboard Gigabit Ethernet
     o	 ZyXEL GN650-T 64-bit PCI Gigabit Ethernet NIC (ZX1701)
     o	 ZyXEL GN670-T 32-bit PCI Gigabit Ethernet NIC (ZX1702)

DIAGNOSTICS

     vge%d: couldn't map memory  A fatal initialization error has occurred.

     vge%d: couldn't map ports	A fatal initialization error has occurred.

     vge%d: couldn't map interrupt  A fatal initialization error has occurred.

     vge%d: failed to enable memory mapping!  The driver failed to initialize
     PCI shared memory mapping.  This might happen if the card is not in a
     bus-master slot.

     vge%d: watchdog timeout  The device has stopped responding to the net-
     work, or there is a problem with the network connection (cable).

SEE ALSO

     arp(4), miibus(4), netintro(4), ng_ether(4), polling(4), vlan(4),
     ifconfig(8)

HISTORY

     The vge device driver first appeared in FreeBSD 5.3.

AUTHORS

     The vge driver was written by Bill Paul <wpaul@windriver.com>.

FreeBSD 5.4		       November 24, 2004		   FreeBSD 5.4

SPONSORED LINKS